TESTS LIST

CONTACTS Via Praga 22, 38121 - Trento (TN) Italy +39 0461 994899 +39 0461 994899 info@mated.it info@pec.mated.it
MATED S.R.L. Via Praga 22 38121 - Trento (TN) - Italy R.I. : TN-203743 VAT : 02150620223

Here are summarized the range of tests and analyzes that MATED S.r.l. performs regularly.
If the method of interest is not mentioned, we invite you to contact our technicians for verification.

2-II-3 LIGHT AGEINGXenon light ageing
AfPS GS PAKPolycyclic aromatic hydrocarbons (PAH) - PAH research
Analisi al microscopioMicroscope analysis
Analisi SEM/EDSScanning electron microscopy analysis
API 5L2 Appendix FHydraulic blistering
API 5L7 Appendix 11Cathodic disbondment
API 5L7 Appendix 13Flexibility
API 5L7 Appendix 16Hot water soak
ASTM A1038Metallic coatings - Portable Hardness Testing by the Ultrasonic Contact Impedance Method
ASTM A380 / A380MStainless steel - Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems
ASTM A90 / A90MWeight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings
ASTM B117Organic and inorganic coatings on metallic substrate - Standard Practice for Operating Salt Spray (Fog) Apparatus
ASTM B117 and ASTM D5894Painted metal - Salt spray and Cyclic Salt Fog-UV Exposure
ASTM B244Thickness of Nonconductive Coatings on Nonmagnetic Basis Metals
ASTM B487Coating - Standard Test Method for Measurement of Metal and Oxide Coating Thickness by Microscopical Examination of Cross Section
ASTM B504Metallic Coatings - Measurement of Thickness by the Coulometric Method
ASTM B764Metallic coatings - Simultaneous Thickness and Electrode Potential Determination of Individual Layers in Multilayer Nickel Deposit (STEP Test)
ASTM C177Thermal insulation - Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus
ASTM C1784Building materials - Using a Heat Flow Meter Apparatus for Measuring Thermal Storage Properties of Phase Change Materials and Products
ASTM C372Linear Thermal Expansion of Porcelain Enamel and Glaze Frits and Fired Ceramic Whiteware Products by the Dilatometer Method
ASTM C518Building materials and products - Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
ASTM C531Standard Test Method for Linear Shrinkage and Coefficient of Thermal Expansion of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes
ASTM C539Standard Test Method for Linear Thermal Expansion of Porcelain Enamel and Glaze Frits and Ceramic Whiteware Materials by Interferometric Method
ASTM C824Standard Practice for Specimen Preparation for Determination of Linear Thermal Expansion of Vitreous Glass Enamels and Glass Enamel Frits by Dilatometer Method
ASTM C832Standard Test Method of Measuring Thermal Expansion and Creep of Refractories Under Load
ASTM D 2369Paint and varnishes - Volatile Content of Coatings
ASTM D 297 par. 16.3Rubber Products - Density - Hydrostatic method
ASTM D 429, Method BRubber Property - Adhesion to Rigid Substrates - Stripping test
ASTM D 445Petroleum products - Kinematic Viscosity of Transparent and Opaque Liquids
ASTM D 942Lubricating Greases - Oxidation Stability of by the Oxygen Pressure Vessel Method
ASTM D1000 21÷27Thickness
ASTM D1000 46÷53Adhesion strength
ASTM D1002Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)
ASTM D1003Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM D1084 Method BAdhesives - Standard Test Methods for Viscosity of Adhesives
ASTM D1148Rubber - Discoloration from Ultraviolet (UV) or UV/Visible Radiation and Heat Exposure of Light-Colored Surfaces
ASTM D1238Plastics - Melt Flow Rates of Thermoplastics by Extrusion Plastometer
ASTM D149, Method ASolid Electrical Insulating Materials - Dielectric Breakdown Voltage and Dielectric Strength at Commercial Power Frequencies
ASTM D150Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation
ASTM D1525Plastics - Vicat Softening Temperature of Plastics
ASTM D1621Rigid Cellular Plastics - Compressive Properties
ASTM D1622Rigid Cellular Plastics - Apparent Density
ASTM D1693Plastics - Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
ASTM D1729Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials
ASTM D1894Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting
ASTM D1921Plastic Materials - Particle Size (Sieve Analysis)
ASTM D217Lubricating Grease - Cone Penetration
ASTM D2240Rubber Property - Durometer Hardness
ASTM D2244Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
ASTM D2247Paints and Varnishes - Water Resistance of Coatings in 100?Relative Humidity
ASTM D2304Thermal Endurance of Rigid Electrical Insulating Materials
ASTM D2454Determining the Effect of Overbaking on Organic Coatings
ASTM D2457Specular Gloss of Plastic Films and Solid Plastics
ASTM D2485Evaluating Coatings For High Temperature Service
ASTM D256Plastics - Izod -notched impact strength
ASTM D257Standard Test Methods for DC Resistance or Conductance of Insulating Materials
ASTM D2583Reinforced and nonreinforced rigid plastics - Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor
ASTM D2584Reinforced Resins - Ignition Loss of Cured Reinforced Resins
ASTM D2621Miscellaneous materials - Standard Test Method for Infrared Identification of Vehicle Solids From Solvent-Reducible Paints
ASTM D2805Paints and Varnishes - Hiding Power of Paints by Reflectometry
ASTM D2990Plastics - Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
ASTM D3170 / D3170MCoatings - Standard Test Method for Chipping Resistance of Coatings
ASTM D3171Constituent Content of Composite Materials
ASTM D3330 / D3330MPressure Sensitive Tape - Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape
ASTM D3350 par. 10.1.9Polyethylene Plastics Pipe and Fittings Materials - Thermal stability
ASTM D3359Paints and Varnishes - Adhesion by Tape Test
ASTM D3363Film Hardness by Pencil Test
ASTM D3418Polymers - Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry
ASTM D3835Plastics - Determination of Properties of Polymeric Materials by Means of a Capillary Rheometer
ASTM D3884Textile Fabrics - Abrasion Resistance
ASTM D3895Polymers - Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry
ASTM D395Rubber Property - Compression Set - Costant deflection in air
ASTM D3985Plastics - Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor
ASTM D4060Paints and varnishes - Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
ASTM D412Vulcanized Rubber and Thermoplastic Elastomers - Tension
ASTM D4145Paints and varnishes - Standard Test Method for Coating Flexibility of Prepainted Sheet
ASTM D4228Qualification of Coating Applicators for Application of Coatings to Steel Surfaces
ASTM D4274Polyurethane Raw Materials - Hydroxyl Numbers of Polyols
ASTM D4289Lubricating Greases and Fluids - Elastomer Compatibility
ASTM D4329Plastics - Standard Practice for Fluorescent Ultraviolet (UV) Lamp Apparatus Exposure of Plastics
ASTM D4541Paints and varnishes - Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM D4587Paints and Varnishes - Fluorescent UV-Condensation Exposures
ASTM D4595Geotextiles fibers - Tensile Properties of Geotextiles by the Wide-Width Strip Method
ASTM D4672Polyurethane Raw Materials - Water Content
ASTM D4752Standard Practice for Measuring MEK Resistance of Ethyl Silicate (Inorganic) Zinc-Rich Primers by Solvent Rub
ASTM D4812Unnotched Cantilever Beam Impact Resistance of Plastics
ASTM D4889Polyurethane Raw Materials - Viscosity of Crude or Modified Isocyanates
ASTM D5026Plastics - Dynamic Mechanical Properties: In Tension
ASTM D5155Polyurethane Raw Materials - Isocyanate Content of Aromatic Isocyanates
ASTM D5162Discontinuity (Holiday) Testing of Nonconductive Protective Coating on Metallic Substrates
ASTM D522Paints and varnishes - Mandrel Bend Test of Attached Organic Coatings
ASTM D523Specular gloss
ASTM D5381Pigments and Extenders - X-Ray Fluorescence (XRF) Spectroscopy of Pigments and Extenders
ASTM D542Plastics - Standard Test Method for Index of Refraction of Transparent Organic Plastics
ASTM D5420Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)
ASTM D5630Plastics - Ash Content in Plastics
ASTM D570Plastics - Water Absorption
ASTM D575Rubber - Rubber Properties in Compression
ASTM D6099Polyurethane Raw Materials - Acidity in Moderate to High Acidity Aromatic Isocyanates
ASTM D6226Rigid Cellular Plastics - Open Cell Content of Rigid Cellular Plastics
ASTM D624Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers
ASTM D635Rate of Burning and-or Extent and Time of Burning of Plastics in a Horizontal Position
ASTM D638Plastics - Tensile Properties
ASTM D648Plastics - Deflection Temperature Under Flexural Load in the Edgewise Position
ASTM D6943Protective Coatings and Linings - Immersion Testing
ASTM D695Compressive Properties of Rigid Plastics
ASTM D696Plastics - Coefficient of Linear Thermal Expansion of Plastics Between -30°C and 30°C with a Vitreous Silica Dilatometer
ASTM D7191Plastics - Standard Test Method for Determination of Moisture in Plastics by Relative Humidity Sensor
ASTM D7205 / D7205MTensile Properties of Fiber Reinforced Polymer Matrix Composite Bars
ASTM D732Plastics - Standard Test Method for Shear Strength of Plastics by Punch Tool
ASTM D746Plastics and elastomers - Brittleness temperature by impact
ASTM D7869Coatings - Xenon Arc Exposure Test with Enhanced Light and Water Exposure
ASTM D790Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
ASTM D792Density and Specific Gravity (Relative Density) of Plastics by Displacement
ASTM D817 par. 7-8-9Ash test
ASTM D870Coating - Standard Practice for Testing Water Resistance of Coatings Using Water Immersion
ASTM D937Petrolatum - Cone Penetration
ASTM D968Standard Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive
ASTM D991Rubber vulcanized or thermoplastic - Volume Resistivity
ASTM E10Metallic Materials - Brinell Hardness of Metallic Materials
ASTM E1019Metals - Chemical analysis of Carbon and Sulfur
ASTM E1252General Techniques for Obtaining Infrared Spectra for Qualitative Analysis
ASTM E1269Plastics - Specific Heat Capacity by Differential Scanning Calorimetry
ASTM E1356Assignment of the Glass Transition Temperatures by Differential Scanning Calorimetry
ASTM E1476 par. 7.1Metals Identification, Grade Verification and Sorting - X-ray fluorescence spectrometry
ASTM E1578Membrane Switch - Standard Test Method for Contact Closure Cycling of a Membrane Switch
ASTM E168General Techniques of Infrared Quantitative Analysis
ASTM E179Standard Guide for Selection of Geometric Conditions for Measurement of Reflection and Transmission Properties of Materials
ASTM E1933Measuring and Compensating for Emissivity Using Infrared Imaging Radiometers
ASTM E2109Thermal spray coatings - Determining Area Percentage Porosity
ASTM E228Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer
ASTM E28Plastics - Softening Point of Resins Derived from Pine Chemicals and Hydrocarbons, by Ring-and-Ball Apparatus
ASTM E2937Paint and varnish - Infrared Spectroscopy in Paint Examinations
ASTM E3 + ASTM E407Metallic materials - Micrographic examination
ASTM E3061Aluminium Alloys - Analysis of Aluminum by Inductively Coupled Plasma Atomic Emission Spectrometry
ASTM E350Metals - Carbon steel low-alloy steels - Chemical analysis of Silicon and Manganese
ASTM E430Paint and varnish - Measurement of Gloss of High-Gloss Surfaces by Abridged Goniophotometry (DOI)
ASTM E573Internal Reflection Spectroscopy (ATR)
ASTM E793Enthalpies of Fusion and Crystallization by Differential Scanning Calorimetry
ASTM E797 / E797MMeasuring Thickness by Manual Ultrasonic Pulse-Echo Contact Method
ASTM E831Linear Thermal Expansion of Solid Materials by Thermomechanical Analysis
ASTM E903Plastic materials - Solar Absorptance, Reflectance, and Transmittance of Materials Using Integrating Spheres
ASTM E967Temperature Calibration of Differential Scanning Calorimeters and Differential Thermal Analyzers
ASTM F1978Thermal spray coatings - Standard Test Method for Measuring Abrasion Resistance of Metallic Thermal Spray Coatings by Using the Taber Abraser
ASTM F433Standard Practice for Evaluating Thermal Conductivity of Gasket Materials
ASTM F510 / F510MResistance to Abrasion of Resilient Floor Coverings Using an Abrader with a Grit Feed Method
ASTM G14Pipeline Coatings - Impact Resistance by falling weight
ASTM G155 Method 7ANon-metallic materials - Xenon arc light exposure - Method 7A
ASTM G17Penetration Resistance of Pipeline Coatings (Blunt Rod)
ASTM G19Disbonding Characteristics of Pipeline Coatings by Direct Soil Burial (Withdrawn 2010)
ASTM G20Chemical Resistance of Pipeline Coatings
ASTM G42Rubber vulcanized or thermoplastic - Cathodic Disbonding
ASTM G53Methods of exposure to laboratory light sources
ASTM G8Standard Test Methods for Cathodic Disbonding of Pipeline Coatings
ASTM G85Paint and varnish - Modified Salt Spray (Fog) Testing
ASTM G9Water Penetration into Pipeline Coatings
ASTM G95Cathodic Disbondment Test of Pipeline Coatings (Attached Cell Method)
AWWA C203COAL-TAR PROTECTIVE COATINGS AND LININGS FOR STEEL WATER PIPES
AWWA C209Tape Coatings for Steel Water Pipe and Fittings
AWWA C210Liquid-Epoxy Coatings and Linings for Steel Water Pipe and Fittings
AWWA C213Fusion-Bonded Epoxy Coatings and Linings for Steel Water Pipe and Fittings
AWWA C214Tape Coatings for Steel Water Pipe
AWWA C215Extruded Polyolefin Coatings for the Exterior of Steel Water Pipelines
AWWA C216Heat-Shrinkable Cross-Linked Polyolefin Coatings for Steel Water Pipe and Fittings
AWWA C217Microcrystalline Wax and Petrolatum Tape Coating Systems for Steel Waer Pipe and Fittings
AWWA C218Liquid Coating for Aboveground Steel Water Pipelines and Fittings
AWWA C222Polyurethane Coatings for the Interior and Exterior of Steel Water Pipe and Fittings
AWWA C224Nylon-11 Based Polyamide Coating System for the Interior and Exterior of Steel Water Pipe, Connections, Fittings and Special Sections
AWWA C225Fused Polyolefin Coating System for the Exterior of Steel Water Pipelines
AWWA C229Fusion-Bonded Polyethylene Coatings for Steel Water Pipe and Fittings
AWWA C550Protective Interior Coatings for Valves and Hydrants
AWWA C605Underground Installation of Polyvinyl Chloride (PVC) and Molecularly Oriented Polyvinyl Chloride (PVCO) Pressure Pipe and Fittings
AWWA C620Spray-Applied In-Place Epoxy Lining of Water Pipelines, 3 In. (75 mm) and Larger
AWWA C900Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated Fittings, 4 In. - 60 In. (100 mm - 1,5000 mm)
AWWA C901Polyethylene (PE) Pressure Pipe and Tubing, 1-2 In. (13 mm) - 3 In. (76 mm), for Water Service
AWWA C903Polyethylene-Aluminum-Polyethylene (PE-AL-PE) Composite Pressure Pipe, 12 mm(1-2 In.) - 51 mm (2 In.), for Water Service
AWWA C904Cross-Linked Polyethylene (PEX) Pressure Pipe, 1-2 In. (12 mm) - 3 In. (76 mm), for Water Service
AWWA C906Polyethylene (PE) Pressure Pipe and Fittings, 4 In. Through 65 In (100 mm Through 1,650 mm) for Waterworks
AWWA C907Injection-Molded Polyvinyl Chloride (PVC) Pressure Fittings, 4 In. - 24 In. (100 mm Through 300 mm) for Water, Wastewater and Reclaimed Water Services
AWWA C909Molecularly Oriented Polyvinyl Chloride (PVCO) Pressure Pipe, 4 In. - 24 In. (100 mm - 600 mm) for Water, Wastewater, and Reclaimed Water Service
AWWA C950Fiberglass Pressure Pipe
BA QA 101PViscosity Measurement
BMW AA-0054Resistance of Coatings to Car-wash Machines
BMW AA-0055Chemical resistance test of surfaces
BMW AA-0101Reflectometer Value (Gloss)
BMW AA-0180Cross hatch testing
BMW AA-0213Condensation Water Constant Atmosphere Test
BMW AA-0224Cyclic corrosion
BMW AA-0324Saltspray-Test
CEI EN 60529Degrees of protection of the enclosures - IP classification
CEN/TS 13130-13Determination of 2,2-bis(4-hydroxyphenyl)propane (Bisphenol A) in food simulants
CHNCHN elemental analysis
Cicli di pressionePressure cycles
CNR IRSA Q24 VOL3 17Cianuri totali (mg-kg)
CSA Z245.20 par.12.1Plant-applied external coatings for steel pipe - Cure time of epoxy powder
CSA Z245.20 par.12.10Plant-applied external coatings for steel pipe - Cross-section and interface porosity
CSA Z245.20 par.12.11Plant-applied external coatings for steel pipe - Flexibility of the coating
CSA Z245.20 par.12.12Plant-applied external coatings for steel pipe - Impact resistance of the coating
CSA Z245.20 par.12.13Plant-applied external fusion bond epoxy coatign for steel pipe - Strained Coating Cathodic Disbondment
CSA Z245.20 par.12.14Plant-applied external coatings for steel pipe - Adhesion of the coating
CSA Z245.20 par.12.2Plant-applied external coatings for steel pipe - Gel time of epoxy powder
CSA Z245.20 par.12.4Plant-applied external coatings for steel pipe - Moisture of the epoxy powder
CSA Z245.20 par.12.5Plant-applied external coatings for steel pipe - Particle size
CSA Z245.20 par.12.6Plant-applied external fusion bond epoxy coatign for steel pipe - Density
CSA Z245.20 par.12.7Plant-applied external coatings for steel pipe - Thermal characteristics of the epoxy powder and coating
CSA Z245.20 par.12.8Fusion bond epoxy coating for steel - Cathodic disbondment of the coating
CSA Z245.21 par.12.3Plant-applied external polyethylene coating for steel pipe - Cathodic disbonding of the coating
CSS PdP-SD1701 rev.0 del 14/12/18Apparent Density tests after 96 hours of immersion in tap water at pressure of 12 bar at ambient temperature
DBL 5416 par.12.4Cross cut with adhesive tape application and removal
DBL 5416 par.12.6Steam jet test
DBL 5416 par.12.7 Method 1Climatic cycle test
DBL 5555 par.8Finished parts and semi-finished products - Hot-storage behaviour of plastics
Definito dal clienteThermal cycle / Cyclic ageing
DIN 30670 Annex BPolyethylene coatings on steel pipes and fittings - Degree of cure of the epoxy resin layer
DIN 30670 Annex CPolyethylene coatings on steel pipes and fittings - Cathodic disbondment (CD test)
DIN 30670 Annex DPolyethylene coatings on steel pipes and fittings - Peel strength
DIN 30670 Annex FPolyethylene coatings on steel pipes and fittings - Allungamento a rottura +23°C
DIN 30670 Annex GPolyethylene coatings on steel pipes and fittings - MFR - On delivery material over after application
DIN 30670 Annex GPolyethylene coatings on steel pipes and fittings - Melt Mass-flow rate
DIN 30670 Annex HPolyethylene coatings on steel pipes and fittings - Impact resistance and low temperature impact resistance
DIN 30670 Annex IPolyethylene coatings on steel pipes and fittings - Indentation resistance
DIN 30671 par. 5.6Thermoset plastic coatings for buried steel pipes - Flexibility
DIN 30672-1Field coating materials for corrosion protection of buried pipelines - Part 1: Requirements and product testings
DIN 30672-2Field coating materials for corrosion protection of buried pipelines - Part 2: Application and quality control on site
DIN 30672-2 Appendix CField coating materials for corrosion protection of buried pipelines - Part 2: Application and quality control on site - Resistance to peeling
DIN 40050-9Road Veichles - Degrees of protection (IP code)
DIN 50018Corrosion testing - Testing in a saturated atmosphere in the presence of sulfur dioxide
DIN 51045-1Determination of the thermal expansion of solids - Part 1: Basic rules
DIN 51045-2Determination of linear thermal expansion of solids - Part 2: Testing of fired fine ceramic materials using the dilatometer method
DIN 51045-3Determination of linear thermal expansion of solids - Part 3: Testing of non-fired fine ceramic materials using the dilatometer method
DIN 51045-4Determination of linear change of solids by thermal effect using the dilatometer method - Part 4: Testing of fired heavy ceramic materials
DIN 51045-5Determination of linear change of solids by thermal effect using the dilatometer method - Part 5: Testing of non-fired heavy ceramic materials
DIN 51130Testing of floor coverings - Determination of the anti-slip property - Workrooms and fields of activities with slip danger - Walking method - Ramp test
DIN 51739Testing of solid fuels - Determination of the dilatation of coal
DIN 51909Solid matters - Testing of carbon materials - Determination of coefficient of linear thermal expansion solid matters
DIN 53236-AColouring materials - Conditions of measurement and evaluation for the determination of colour differences for paint coatings, similar coatings and plastics
DIN 53380-3Plastics - Determination of gas trasmission rate - Part3: Oxygen-specific carrier gas method for testing of plastics films and plastics mouldings
DIN 53491Testing of Plastics - Determination of the Refractive Index and Dispersion
DIN 75201Determination of the fogging characteristics of trim materials in the interior of automobiles
DM 21/03/1973 GU n° 104 20/04/1973 All IV Se1DM 21-03-1973 GU n° 104 20-04-1973 All IV Sez 1 + DM 26-04-1993 GU n° 162 13-07-1993 All III + DM 24-09-1996 gu N° 264 11-11-1996 + DM 28-03-2003 GU n°125 31-05-2003 + DM 22-12-2005 GU n° 37 14-02-2005
DNVGL-RP-0416Corrosion protection for wind turbines
DOC. NO. KOC-P-004 Pt. 7TESTS FOR HEAT SHRINK SLEEVE - Soil stress (shear test
DVP 15.3 - Lifetime test Material agingDVP 15.3 - Lifetime test Material aging
EN 10289 par.7.15Steel tubes and fittings for onshore and offshore pipelines - External liquid applied epoxy and epoxy-modified coatings - Infra-red scan obtained with a KBr standard disk
EN 10290 Annex CExternal liquid applied polyurethane and polyurethane-modified coatings - Impact test
EN 10290 Annex DAdhesion test - Resistance to removal
EN 10290 Annex ECathodic disbondment
EN 10290 Annex FSteel tubes and fittings for onshore and offshore pipelines - External liquid applied polyurethane and polyurethane-modified coatings - Specific electrical insulation resistance test
EN 10290 Annex GAdhesion test after immersion in tap water
EN 10290 Annex HIndentation resistance
EN 10290 Annex JSteel tubes and fittings for onshore and offshore pipelines - External liquid applied polyurethane and polyurethane-modified coatings - Thermal ageing
EN 10290 Annex KFlexibility
EN 10290 par.7.17Elongation
EN 1186-1 + EN 1186-3Migrazione globale in simulante alimentare acquoso per immersione totale
EN 1186-1 + EN 1186-5Migrazione globale in simulante alimentare acquoso mediante mediante l uso di una cella - Simulante C - Etanolo al 20 (v-v) - 10gg a 40°C
EN 1186-13 Method BMigrazione globale in simulante E - Poli(ossido di 2,6-difenil-pfenilene) (MPPO)
EN 12691Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Determination of resistance to impact
EN 1297Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets for roof waterproofing - Method of artificial ageing by long term exposure to the combination of UV radiation, elevated temperature and water
EN 13071-1 par.6.6Stationary waste containers up to 5 000 l, top lifted and bottom emptied - Part 1: General requirements - Weathering and ageing
EN 1401-1 par.13.2Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the systems - Minimum required marking of pipes
EN 1401-1 par.7.2 -1, -2, -3, -4, -5Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the systems - Dimensions of pipes
EN 1401-1 par.7.4.1.1 e 7.4.1.2Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the systems - Dimensions of socket and spigot
EN 1401-1 par.8.1.1.2 + ISO 3127Thermoplastics pipes - Determination of resistance to external blows — Round-the-clock method
EN 14901-1Ductile iron pipes, fittings and accessories - Requirements and test methods for organic coatings of ductile iron fittings and accessories - Part 1: Epoxy coating (heavy duty)
EN 1604Thermal insulating products for building applications - Dimensional stability under specified temperature and humidity conditions
EN 2507-1Thermoplastics pipes and fittings - Vicat softening temperature - Part 1: General test method
EN 388 +A1 p.6.2Protective gloves against mechanical risks - Blade cut resistance
EN 660-2 /A1Resilient floor coverings - Determination of wear resistance - Part 2: Frick-Taber test
EN 821-1Advanced technical ceramics - Monolithic ceramics - - Thermo-physical properties - Part 1: Determination of thermal expansion
EN 821-2Advanced technical ceramics - Monolithic ceramics - - Thermo-physical properties. Part 2: Determination of thermal diffusivity by the laser flash (or heat pulse) method
EPA 3550CSemi-volatile Organic Compounds - Semi-volatile organic compounds analisys using ultrasonic extraction
EPA 3550C + EPA8270DAmmine aromatiche mg-kg
EPA 5021AVolatile organic compounds - Volatile organic compounds analisys using equilibrium headspace analysis
EPA 6010DRestrizioni definite nell Allegato II del Reg.10-2011-UE e Reg. 752-2017 Parametro: Migrazione specifica Al, Ba, Co, Fe, Li, Mn, Ni, Cu e Zn
EPA 6010D + EPA 3051Ascreening of the 8 metals mainly present
EPA3550C + EPA8015DSolventi clorurati mg-kg
EPA5021A + EPA8260CBenzene mg-kg
ES805-001 Rev4 par.3.4Decorative chrome plating - Adhesion to metal substrate - Heat-quench (for high temperature applications) and reverse band saw cut tests
ES805-001 Rev4:2018 par.3.5Decorative chrome plating - Corrosion
ES805-07011 v13 par.6.4Humidity Resistance
ES805-34307 v4 par.6.5High temperature exhaust coatings - Corrosion resistance
ES805-34307 v4 par.6.6High temperature exhaust coatings - Thermal exposure with corrosion
ESPEC805-060 rev3 par.3Zinc-Nickel Plating - Adhesion after heat quench
ESPEC805-060 rev3 par.4Zinc-Nickel Plating - Corrosion performance
ETAG 004 par. 5.1.4.3.1External thermal insulation - Pull-through test on fixings
FCA 50432/01Plastics - Determination of the stress cracking resistance
FCA 9.55254 par.2.5.4.2Resistance to hot dry
FCA 9.55254 par.2.5.4.3Resistance to heat stroke
FCA 9.55254 par.2.5.4.4Resistance to thermal cycle
FCA LP 7N022Cold impact performance
FCA LP-463DD-18-02 Method AAutomotive plastics - Method A: Scratch resistance
FCA LP-463DD-18-02 Method BAutomotive plastics - Method B: Mar resistance
FCA LP-463PB-54-01Crock mar resistance
FCA PF 90062 par.5.12Dimensional Stability
FCA PF 90062 par.5.13Thermal shock
FCA PF 90062 par.5.14Thermal Cycling
FCA PF 90062 par.5.15Humidity resistance
FCA PF 90062 par.5.2 + FCA LP 7N022Cold impact performance
FCA PF 90223 par.5.1.2Instrument Panel - Heat aging
FCA PF 90223 par.5.1.4Instrument panel - Thermal cycle
FCA PF.90155 par.5.1Thermal shock
FCA PF.90155 par.5.2Thermal cycling
FCA PF.90155 par.5.3Cold impact
FCA PF.90155 par.5.4Humidity resistance
FCA PF.90155 par.5.5Extended heat ageing
FCA PF.90155 par.5.6Dimensional stability
FCA PF.90155 par.5.8Corrosion of mechanical fasteners
FCA PF.90155 par.5.9Chemical resistance
FIAT 50180-A1Corrosion Tests
FIAT 50184 - Metodo BDamp heat behavior
FIAT 50451Vehicle Exteriors - Accelerated aging by atmospheric agents
FIAT 50451/01Accelerated aging in sunlight
FIAT 50457Non-metallic materials - Specular gloss for paints, varnishes and enamels by glossmeter.
FIAT 50461Paints and varnishes - Adhesion resistance test of inorganic and organic trims by squaring off.
FIAT 50470Water immersion resistance test
FIAT 50471/01Alternating ultraviolet radiation-humidity resistance test
FIAT 50488Determination of the abrasion resistance of protective coatings by means of metallic grit
FIAT 7.G2183Determination of internal impurities in components of fluid circulation systems
FIAT 7-M0005Paints and varnishes - Scratch resistance
FIAT 9.02132/02 par.2.3.7Resistance to thermal cycles
FIAT 9.02132/02 par.2.3.9Heat age Exposure Test
FIAT 9.02215 par.5.2Dimensional Stability
FIAT 9.02215 par.5.3Resistance to cold impact
FIAT 9.02215 par.5.4Resistance to chemicals
FIAT 9.02215 par.5.5Burning velocity
FIAT 9.02215 par.9.3Thermal ageing
FIAT 9.02215 par.9.4Resistance to thermal cycles
FIAT 9.03109:2008 par.2.10Damp heat behavior
FIAT 9.03109:2008 par.2.11Resistance to thermal cycles
FIAT 9.03109:2008 par.2.12Low temperature behaviour
FIAT 9.03109:2008 par.2.9.1Dimensional Stability
FIAT 9.03109:2008 par.2.9.2Heat Stroke
FIAT 9.03147 par.2.19Adhesion - resistance to detachment by shear
FIAT 9.07301 par.2.10Damp heat behavior
FIAT 9.07301 par.2.11Behaviour in cold weather
FIAT 9.07301 par.2.12Resistance to cold impact
FIAT 9.07301 par.2.7Thermal ageing
FIAT 9.07301 par.2.8Hot stiffness
FIAT 9.07301 par.2.9Resistance to thermal cycles
FIAT 9.55253 par.2.10.2Dimensional Stability
FIAT 9.55253 par.2.10.3Heat stroke
FIAT 9.55253 par.2.10.4Thermal ageing
FIAT 9.55253 par.2.11Resistance to thermal cycles
FIAT 9.55253 par.2.12Damp heat aging
FIAT 9.55253 par.2.14Resistance to cold impact
FIAT 9.55253 par.2.17Resistance to chemicals
FIAT 9.55253 par.2.18Burn rate test
FIAT 9.55253 par.2.7.3Thermal shock resistance
FIAT 9.55842/01 par.2.10UV resistance
FIAT 9.55842/01 par.2.12Resistance to damp
FIAT 9.55842/01 par.2.13Resistance to water
FIAT 9.55842/01 par.2.14Resistance to temperature variations
FIAT 9.55842/01 par.2.15Resistance to chemicals
FIAT 9.55842/01 par.2.16Resistance to alchool
FIAT 9.55842/01 par.2.17Resistance to fuel
FIAT 9.55842/01 par.2.20Resistance to stone-chipping
FIAT 9.55842/01 par.2.22Scratching test by brushing
FIAT 9.55842/01 par.2.4Visual inspection
FIAT 9.55842/01 par.2.5Thickness
FIAT 9.55842/01 par.2.6Hardness
FIAT 9.55842/01 par.2.7Adhesion
FIAT 9.55842/01 par.2.9Accelerated weathering with adhesion and gloss evaluation
FORD FLTM BO 162-01Resistance to scratch and mar
IEC 243-1Methods of test for electric strength of solid insulating materials - Part 1: Test at power frequencies
IEC 60216-1Electrical insulating materials - Thermal endurance properties - Part 1: Ageing procedures and evaluation of test results
IEC 60243-1 - max 60kV;Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
IEC 60695-10-2Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method
IEC 60695-11-10:2013Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods
IEC 61215 par.10.10Crystalline silicon terrestrial photovoltaic (PV) modules - Design qualification and type approval
IEC 61215 par.10.11Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Thermal cycling test
IEC 61215 par.10.12Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Humidity-freeze test
IEC 61215 par.10.13.2Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Damp heat test
IEC 61215-1Terrestrial photovoltaic (PV) modules - Design qualification and type approval - Part 1: Test requirements
IEC 62108 par.10.6Concentrator photovoltaic (CPV) modules and assemblies - Design qualification and type approval - Thermal Cycling Test
IEC 62108 par.10.7Concentrator photovoltaic (CPV) modules and assemblies - Design qualification and type approval - Damp Heat Test
IEC 62108 par.10.8Concentrator photovoltaic (CPV) modules and assemblies - Design qualification and type approval - Humidity freeze test
IEC 62631-2-1Proprietà dielettriche e resistive di materiali solidi isolanti - Part 2-1: Permeabilità relativa e fattore di dissipazione - Frequenze (0,1 Hz - 10 MHz) - Metodi AC
IEC 62631-3-1Volume resistance and volume resistivity
IMO MSC.215(82)-Annex 1 Appendix 1Paints and varnishes - Wave Tank Test
IMO MSC.215(82)-Annex 1 Appendix 2Paints and varnishes - Condensation chamber test
Invecchiamento in azoto protossido (N2O)Plastic materials - Autoclave with dinitrogen monoxide
ISO 10304-1Amount of chlorides, fluorides, nitrates, nitrites and sulphates
ISO 10477 par. 7.5Flexural strength
ISO 10545-8Ceramic tiles - Part 8: Determination of linear thermal expansion
ISO 11347Ships and marine technology -- Large yachts - Measurement and assessment of the visual appearance of coatings
ISO 11359-2Plastics - Thermomechanical analysis (TMA)
ISO 11443Plastics - Determination of the fluidity of plastics using capillary and slit-die rheometers
ISO 1183-2 Met BPlastics - Specific Gravity - liquid pycnometer method
ISO 12736 Annex IWet thermal insulation coatings for pipelines, flow lines, equipment and subsea structures - Ring shear test
ISO 12736 par.A.2.1Petroleum and natural gas industries — Wet thermal insulation coatings for pipelines, flow lines, equipment and subsea structures - Hydrostatic collapse test
ISO 12736 par.A.3Wet thermal insulation coatings for pipelines, flow lines, equipmeny and subsea structures - Tri-axial compression and creep test
ISO 12944-6Paints and varnishes - Corrosion protection of steel structures by protective paint systems
ISO 12944-9Paints and varnishes - Protective paint systems and laboratory performance test method for offshore and related structures
ISO 13468-1Plastics - Determination of the total luminous transmittance of transparent materials — Part 1: Single-beam instrument
ISO 14125Fibre-reinforced plastic composites - Determination of flexural properties
ISO 1419 Method CRubber- or plastics-coated fabrics - Accelerated-ageing tests: tropical test
ISO 1431-1Rubber, vulcanized or thermoplastic - Resistance to ozone cracking - Part 1: Static and dynamic strain testing
ISO 14420Carbonaceous products for the production of aluminium — Baked anodes and shaped carbon products - Determination of the coefficient of linear thermal expansion
ISO 14782Plastics - Determination of haze for transparent materials
ISO 15105-2Plastics — Film and sheeting - Determination of gas-transmission rate — Part 2: Equal-pressure method
ISO 15113 proc. ARubber - Determination of frictional properties - Procedure A - Initial friction measurements
ISO 15113 proc.BRubber - Determination of frictional properties - Porcedure B - service behaviour
ISO 15113 proc.CRubber - Determination of frictional properties - Procedure C (tests with added lubricants or contaminants)
ISO 1518-1Paints and varnishes - Scratch resistance
ISO 15711Paints and varnishes - Determination of resistance to cathodic disbonding of coatings exposed to sea water
ISO 15741 par. 4.3.6Friction-reduction coatings for the interior pipelines - Resistance to salt spray
ISO 15741 par. 4.3.7Friction-reduction coatings for the interior pipelines - Resistance to artificial ageing
ISO 16145-1Ships and marine technology - Protective coatings and inspection method Dedicated sea water ballast tanks
ISO 16925:2014Paints and varnishes - Determination of the resistance of coatings to pressure water-jetting
ISO 16961Petroleum, petrochemical and natural gas industries - Internal coating and lining of steel storage tanks
ISO 17054Steel - Spectrometry XRF on high alloy steel
ISO 17744Plastics - Determination of specific volume as a function of temperature and pressure (pvT diagram) — Piston apparatus method
ISO 17834Thermal spraying — Coatings for protection against corrosion and oxidation at elevated temperatures
ISO 18468Ductile iron fittings, accessories and their joints and valves - Epoxy coating
ISO 18488Polyethylene (PE) materials for piping systems - Determination of Strain Hardening Modulus in relation to slow crack growth - Test method
ISO 18553Polyolefin - Method for the assessment of the degree of pigment or carbon black dispersion
ISO 18555Metallic and other inorganic coatings - Determination of thermal conductivity of thermal barrier coatings
ISO 18796-1Petroleum, petrochemicals and natural gas industries - Internal coating and lining of carbon steel process vessels — Part 1: Technical requirements
ISO 18797-1Petroleum, petrochemical and natural gas industries -- External corrosion protection of risers by coatings and linings - Elastomeric coating systems-polychloroprene or EPDM
ISO 19277Petroleum, petrochemical and natural gas industries - Qualification testing and acceptance criteria for protective coating systems under insulation
ISO 20795-1 par. 8.5.3.5Ultimate flexural strength and flexural modulus
ISO 20795-2 par. 8.3.2.5Ultimate flexural strength and flexural modulus
ISO 21546Paints and varnishes - Determination of the resistance to rubbing using a linear abrasion tester (crockmeter)
ISO 2176Lubricating grease - Dropping point
ISO 2177Metallic coatings - Measurement of coating thickness — Coulometric method by anodic dissolution
ISO 21809-11Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Coatings for in-field application, coating repairs and rehabilitation
ISO 21809-4Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems Polyethylene coatings (2-layer PE)
ISO 2207Petroleum waxes - Determination of congealing point
ISO 22479Corrosion of metals and alloys - Sulfur dioxide test in a humid atmosphere (fixed gas method)
ISO 22557Paints and varnishes - Scratch test using a spring-loaded pen
ISO 22680Metallic and other inorganic coatings - Measurement of the linear thermal expansion coefficient of thermal barrier coatings
ISO 22969Paints and varnishes - Determination of solar reflectance
ISO 22970Paints and varnishes - Test method for evaluation of adhesion of elastic adhesives on coatings by peel test, peel strength test and tensile lap-shear strength test with additional stress by condensation test or cataplasm storage
ISO 24338Laminate floor coverings - Determination of abrasion resistance
ISO 2602Statistical interpretation of test results
ISO 2815Paints and varnishes - Buchholz indentation test
ISO 3146, Method BPlastics - Melting behaviour (melting temperature or melting range) of semi-crystalline polymers by polarizing-microscope methods
ISO 34-1Rubber, vulcanized or thermoplastic - Determination of tear strength — Part 1: Trouser, angle and crescent test pieces
ISO 3451-1 + EPA 6010D + EPA 3051AAsh characterization - screening of the 8 metals mainly present
ISO 3679Petroleum products in general, Paints and varnishes - Determination of flash no-flash and flash point - Rapid equilibrium closed cup method
ISO 37Rubber, vulcanized or thermoplastic - Determination of tensile stress-strain properties
ISO 4287Geometrical Product Specifications (GPS) - Surface texture: Profile method — Terms, definitions and surface texture parameters
ISO 4433-2Thermoplastics - Resistance to liquid chemicals: polyolefin
ISO 4532Vitreous and porcelain enamels - Determination of the resistance of enamelled articles to impact
ISO 458-2Plastics - Determination of stiffness in torsion of flexible materials -- Part 2 Application to plasticized compounds of homopolymers and copolymers of vinyl chloride
ISO 4623-2Paints and varnishes - Determination of resistance to filiform corrosion Aluminium substrates
ISO 4649Rubber, vulcanized or thermoplastic - Determination of abrasion resistance using a rotating cylindrical drum device
ISO 48-4Rubber, vulcanized or thermoplastic - Determination of hardness - Part 4: Indentation hardness by durometer method (Shore hardness)
ISO 4897Cellular plastics - Determination of the coefficient of linear thermal expansion of rigid materials at sub-ambient temperatures
ISO 5470-1Rubber- or plastics-coated fabrics - Determination of abrasion resistance Taber abrader
ISO 565Granule Size
ISO 604Plastics - Determination of compressive properties
ISO 6270-3Paints and varnishes - Determination of resistance to humidity Condensation (in-cabinet exposure with heated, bubbling water reservoir)
ISO 6452Rubber- or plastics-coated fabrics - Determination of fogging characteristics of trim materials in the interior of automobiles
ISO 6603-2Plastics - Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented impact testing
ISO 6721-1Plastics - Determination of dynamic mechanical properties — Part 1: General principles
ISO 6721-4Plastics - Determination of dynamic mechanical properties Tensile vibration -- Non-resonance method
ISO 6721-5Plastics — Determination of dynamic mechanical properties - Part 5: Flexural vibration — Non-resonance method
ISO 6964 Met.CPolyolefin pipes and fittings - Carbon black content
ISO 75-1Plastics - Determination of temperature of deflection under load — Part 1: General test method
ISO 75-2Plastics - Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 75-3Plastics - Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics
ISO 7765-1Plastics film and sheeting - Determination of impact resistance by the free-falling dart method Staircase methods
ISO 7765-2Plastics film and sheeting - Determination of impact resistance by the free-falling dart method Instrumented puncture test
ISO 7784-1Paints and varnishes - Determination of resistance to abrasion — Part 1: Method with abrasive-paper covered wheels and rotating test specimen
ISO 7991Glass — Determination of coefficient of mean linear thermal expansion
ISO 812Rubber, vulcanized or thermoplastic - Determination of low-temperature brittleness
ISO 816Rubber, vulcanized - Determination of tear strength of small test pieces (Delft test pieces)
ISO 8179-1Ductile iron pipes, fittings, accessories and their joints — External zinc-based coating - Part 1: Metallic zinc with finishing layer
ISO 8179-2Ductile iron pipes, fittings, accessories and their joints — External zinc-based coating - Part 2: Zinc-rich paint
ISO 8256Plastics - Determination of tensile-impact strength
ISO 8301Thermal insulation - Determination of steady-state thermal resistance and related properties - Heat flow meter apparatus
ISO 8302Thermal insulation - Determination of steady-state thermal resistance and related properties -- Guarded hot plate apparatus
ISO 899-1Plastics - Determination of creep behaviour Tensile creep
ISO 899-2Plastics - Determination of creep behaviour Flexural creep by three-point loading
ISO 9142Adhesives - Guide to the selection of standard laboratory ageing conditions for testing bonded joints
ISO 9237Textiles - Determination of the permeability of fabrics to air
ISO 9352Plastics - Determination of resistance to wear by abrasive wheels
ISO 974Plastics - Determination of the brittleness temperature by impact
ISO 9852Unplasticized poly(vinyl chloride) (PVC-U) pipes - Dichloromethane resistance at specified temperature (DCMT) -- Test method
ISO/TR 19402Paints and varnishes - Adhesion of coatings
ISO/TR 21555Paints and varnishes - Overview of test methods on hardness and wear resistance of coatings
ISO/TS 19392-1Paints and varnishes - Coating systems for wind-turbine rotor blades Minimum requirements and weathering
ISO/TS 19397Coatings - Determination of the film thickness of coatings using an ultrasonic gage
IVECO 15-0461Cross-cut adhesion test
IVECO 15-0470Determination of water resistance of paints, enamels, etc.
IVECO 15-0473Determination of solvent resistance of paints, enamels, etc.
IVECO 15-6021Persoz hardness
IVECO 15-6023Resistance to stone chipping of paints, enamels, etc.
IVECO 16-0135 Metodo A1Salt spray test
IVECO 16-0140Damp heat behavior
IVECO 16-0146Rapid temperature change for components and assemblies
IVECO 16-0154Burning rate
IVECO 16-0160 par.5.2 - ScratchScratch test
IVECO 16-0176Burning rate of non-metallic materials
IVECO 16-0180 Met.CResistance to atmospheric agents
IVECO 18-8000 par. 10Thermal cycles resistance
IVECO 18-8000 par. 11Damp heat behavior
IVECO 18-8000 par. 12Resistance to surface damage
IVECO 18-8000 par. 13Indentation
IVECO 18-8000 par. 14Cold impact resistance
IVECO 18-8000 par. 15.1Accelerated aging to atmospheric agents
IVECO 18-8000 par. 15.2Ageing to light
IVECO 18-8000 par. 16Resistance to chemicals
IVECO 18-8000 par. 18Abrasion resistance
IVECO 18-8000 par. 20Hydrolysis resistance
IVECO 18-8000 par. 8.2Surfactant
IVECO 18-8000 par. 9.1Painting cycle simulation
IVECO 18-8000 par. 9.2Dimensional Stability
IVECO 18-8000 par. 9.3Heat Stroke
IVECO 18-8000 par. 9.4Thermal ageing
IVECO 18-8061 par.5.11Dimensional stability
IVECO 18-8061 par.5.12Thermal shock behaviour
IVECO 18-8061 par.5.13Damp heat behaviour
IVECO 18-8061 par.5.15Low temperature behaviour
IVECO 18-8061 par.5.16Thermal cycles
IVECO 18-8061 par.5.17.4Resistance to chemicals
KLT FCA AGS 560KLT FCA AGS
LMBG § 35 L 00.00-6 1Migrazione globale Media nel simulante (mg-kg) Ammine Aromatiche Primarie: Migrazione specifica (mg-kg)
MBN 10494-5 par.5.1.1Manual scratch test
Metodo interno lab.ID93 - ICPMetals - Phosphorus content by humid chemical analysis
MIL-STD-810G method 504.1 Procedure I par.2.2.6Contamination by fluids @23°C
MIL-STD-810G method 504.1 Procedure I par.2.2.6Contamination by fluid @ high temperature
MIL-STD-810G method 508.6 method AFungus
MSL 10.23.0007 par.4.1.1Cross hatch adhesion test
MSL 10.23.0007 par.5.1.1Gloss level
MSL 10.23.0007 par.5.1.2.2Spectrometer colour match
MSL 10.23.0007 par.5.1.3Surface Finish
MSL.10.23.0007 par.4.5Heat Ageing test
NACE No.12 par. 6.5Specification for the Application of Thermal Spray Coatings (Metallizing) of Aluminum, Zinc, and Their Alloys and Composites for the Corrosion Protection of Steel - Bend test
NACE SP0188Paints and varnishes - Discontinuity (Holiday) Testing of New Protective Coatings on Conductive Substrates
NACE SP0394 Appendix AApplication, Performance, and Quality Control of Plant-Applied Single Layer Fusion-Bonded Epoxy External Pipe Coating - Density - Specific gravity
NACE SP0394 Appendix CApplication, Performance, and Quality Control of Plant-Applied Single Layer Fusion-Bonded Epoxy External Pipe Coating - Gel time
NACE SP0394 Appendix DGlass transition and heat of reaction
NACE SP0394 Appendix EPlant-applied Single-Layer Fusion-Bonded Epoxy External Pipe Coating - Moisture analysis determination
NACE SP0394 Appendix FFusion Bonded Epoxy External Pipe Coating - Cathodic disbondment
NACE SP0394 Appendix GPorosity of the coating
NACE SP0394 Appendix HFlexibility test
NACE SP0394 Appendix JHot water soak
NACE SP0394 Appendix KTest for interface contamination of the coating
NACE SP0394 Appendix LApplication, Performance, and Quality Control of Plant-Applied Single Layer Fusion-Bonded Epoxy External Pipe Coating - Particle size - Sieve
NACE SP0394 Appendix MPlant-applied Single-Layer Fusion-Bonded Epoxy External Pipe Coating - Total volatile-moisture of epoxy powder mass loss
NACE SP0395(formerly RP0395), Fusion-Bonded Epoxy Coating of Steel Reinforcing Bars -
NACE TM0104 sect. 12Offshore Platform Ballast Water Tank Coating System Evaluation - Thick-Film Cracking Test
NACE TM0174Laboratory Methods for the Evaluation of Protective Coatings and Lining Materials on Metallic Substrates in Immersion Service
NACE TM0404 sect. 12Offshore Platform Coating System Evaluation - Flexibility Test
NACE TM0404 sect. 9Offshore Platform Coatings System Evaluation - Thermal-Cycling Resistance Test
NATIONALGRID T.SC.PW.6.1 J229 Appendix JFBE coating - Evaluation of resistance to heat blistering
NATIONALGRID T.SC.PW.6.1 J229:2018 Appendix FFBE coating - Impact resistance
NES M0141 par.6.2.3Chipping resistance characteristics
NES M0141 par.6.2.8Abrasion resistance characteristics
NES M0141 par.6.4.1 BWeathering resistance characteristics - Accelerated exposure
NF A 49-711 Appendix KExternal three layer polypropylene coating applicated by extrusion - Cathodic disbonding test under negative polarization
NF F 31-112Railway rolling stock - Protection in relation to graffiti - Tests procedures and methodes of valuation, behaviour of materials and products of expulsion - Matériel roulant ferroviaire - Protection vis-à-vis des graffiti - Procédures d essais et méthodes d évaluation du comportement des matériaux et des produits d élimination
NF T60-121Petroleum products - Determination of the conventional melting point of petroleum waxes and petroleum jellies
NF T60-191Petroleum products and lubricating greases - Oil separation on storage - method under pressure, static conditions
NWSP 70.1Textiles - Determination of permeability of fabrics to air
PdP-SD1701 rev0 + ISO1183-1 + ASTM D2842Apparent saturated density in water after 96hours of water immersion at 12 bar
PdP-SD2010 rev0PU foam - Apparent saturated density in water
PF.90131 par.5.1.1Heat age Exposure Test
PF.90131 par.5.1.2Thermal cycle exposure test
PF.90131 par.5.1.3Humidity Aging Exposure Test
PF.90131 par.5.1.4Artificial Light Exposure Test
PF.90131 par.5.2.1Mold-in-Color Plastic Scratch and Mar Resistance
PF.90131 par.5.3.2Corrosion resistance test
PV 3330Elastomer O-Rings - Compression Set (Plastic Deformation)
PV 3952Scratch Resistance Test
PV 3974Determination of the Mar resistance
PV 3989Cold behavior for plastic components - Ball drop test
QUALICOAT - MACHU TEST par.2.11Liquid and powder organic coatings on aluminium - Mach test
RCSC Appendix A, sect. A.2.2Specification for Structural Joints Using High-Strength Bolts - DFT measurements
RCSC Appendix A, sect. A.3Specification for Structural Joints Using High-Strength Bolts - Slip coefficient determination
RCSC Appendix A, sect. A.4Specification for Structural Joints Using High-Strength Bolts - Tension creep determination
Renault D421235Plastic or rubber parts - Impact behaviour
RFI DTC SI PS SP IFS 001 AGeneral technical specifications for civil works.
SAE J 2527Suface veichle - Accelerated Exposure of Automotive Exterior Materials Using a Controlled Irradiance Xenon-Arc Apparatus
SAE J1756Determination of the Fogging Characteristics of Interior Automotive Materials
SAE J2334Laboratory Cyclic Corrosion Test
SAE J2412Accelerated weathering
SAE J400Chip Resistance of Surface Coatings
SAE USCAR1-2Salt spray testing and evaluation of fasteners finishes
SPECIFICHE TECNICHE N. F 12 DEL 01.06.2018 - Resistenza allo strappoResistenza allo strappo con sistemi di sicurezza inseriti
SPECIFICHE TECNICHE N. F 12 DEL 01.06.2018 - Resistenza collegamento Passante cintura-Fondina.Resistenza collegamento Passante cintura-Fondina.
SSPC-PA 2Paint application specification no. 2 - Measurement of dry coating thickness
TL 52711 No.11 par.6.11Resistance to chemicals
TL 52711 No.7 par.6.7Stone-chip resistance
TL 52711 No.8 par.6.8Pressure washer test
TL 52711 No.9 par.6.9Water absorption
UL 746BStandard for Polymeric Materials - Long Term Property Evaluations (Thermal Index)
UL 746CStandard for Polymeric Materials - Use in Electrical Equipment Evaluations - Outdoor Suitability
UL 94Plastic materials in devices and appliances - Test for flammability
UNI 10559Paints and varnishes - Determination of abrasion resistance by "TABER" apparatus.
UNI 10667-2 Appendice ARecycled polyethylene - Method for the determination of contamination
UNI 10667-2 Appendix APolyethylene produced from recycled material - Method for the determination of contamination
UNI 7796 par.6Anodic oxidation coatings on aluminium and aluminium alloys - Hard anodic films of great thickness
UNI 8901Prodotti vernicianti - Determinazione della resistenza all urto.
UNI 8941-3Coloured surfaces - Coloured surfaces. Colorimetry
UNI 9099 par. B.1Steel pipes for buried or submerged pipelines - External polyethylene coating applied by extrusion.
UNI 9099 par. B.8.1Ultraviolet (UV) stability
UNI 9099 par. B.9External polyethylene coating applied by extrusion - Cathodic disbondment
UNI 9389Prodotti vernicianti. - Misura della riflessione di pellicole di prodotti vernicianti non metallizzati.
UNI EN 1015-12Mortar for masonry - Determination of adhesive strength to substrate
UNI EN 10289 Annex ASteel Tubes And Fittings For Onshore And Offshore Pipelines - External liquid applied epoxy and epoxy-modified coatings
UNI EN 10289 Annex BExternal liquid applied epoxy and epoxy-modified coatings - Holiday detection test
UNI EN 10289 Annex CSteel tubes and fittings for onshore and offshore pipelines - Impact test
UNI EN 10289 Annex DExternal liquid applied epoxy and epoxy-modified coatings - Adhesion test - Resistance to removal
UNI EN 10289 Annex EExternal liquid applied epoxy and epoxy-modified coatings - Cathodic disbondment test
UNI EN 10289 Annex FSteel tubes and fittings for onshore and offshore pipelines - Specific electrical insulation resistance test
UNI EN 10289 Annex GExternal liquid applied epoxy and epoxy-modified coatings - Adhesion test after immersion in tap water
UNI EN 10289 Annex HExternal liquid applied epoxy and epoxy-modified coatings - Indentation test
UNI EN 10289 Annex JExternal liquid applied epoxy and epoxy-modified coatings - Thermal ageing
UNI EN 10289 par.7.4Steel tubes and fittings for onshore and offshore pipelines - External liquid applied epoxy and epoxy-modified coatings - Appearance
UNI EN 1062-3Coating materials and coating systems for exterior masonry and concrete. - Determination of liquid water permeability
UNI EN 1062-6Coating materials and coating systems for exterior masonry and concrete - Determination of carbon dioxide permeability
UNI EN 1107-1Flexible sheets for waterproofing - Part 1: Bitumen sheets for roof waterproofing - Determination of dimensional stability
UNI EN 12068 Annex BTapes and shrinkable materials for the corrosion protection of burried or immersed steel pipelines - Peeling resistance tape on external tape
UNI EN 12068 Annex CTapes and shrinkable materials for the corrosion protection of burried or immersed steel pipelines - Peeling resistance tape on pipe surface or factory coating
UNI EN 12068 Annex DTapes and shrinkable materials for the corrosion protection of burried or immersed steel pipelines - Lap shear resistance
UNI EN 12068 Annex ETapes and shrinkable materials for the corrosion protection of burried or immersed steel pipelines - Thermal ageing resistance
UNI EN 12068 Annex GTapes and shrinkable materials for the corrosion protection of burried or immersed steel pipelines - Indentation
UNI EN 12068 Annex HTapes and shrinkable materials for the corrosion protection of burried or immersed steel pipelines - Impact resistance
UNI EN 12068 Annex JTapes and shrinkable materials for the corrosion protection of burried or immersed steel pipelines - Specific insulation resistance
UNI EN 12068 Annex KTapes and shrinkable materials for the corrosion protection of burried or immersed steel pipelines - Cathodic disbonding
UNI EN 12068 Annex PTapes and shrinkable materials for the corrosion protection of burried or immersed steel pipelines - Unrolling behavior
UNI EN 12310-2Part 2: Plastic and rubber membrane for waterproofing roofs
UNI EN 12311-2Plastic and rubber sheets for roof waterproofing - Determination of tensile properties
UNI EN 12390-1Concrete - Testing hardened concrete
UNI EN 12390-7Concrete - Testing hardened concrete
UNI EN 12430Thermal insulating products for building applications - Determination of behaviour under point load
UNI EN 12457-2Leaching - Compliance test for leaching of granular waste materials and sludges - One stage batch test at a liquid to solid ratio of 10 l-kg for materials with particle size below 4 mm (without or with size reduction)
UNI EN 12667Building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods
UNI EN 1337-3Structural bearings - Part 3: Elastomeric bearings
UNI EN 1337-9Structural bearings - Protection
UNI EN 13438Paints and varnishes - Powder organic coatings for hot dip galvanised or sherardised steel products for construction purposes
UNI EN 13495Thermal insulation products for building applications - Determination of the pull-off resistance of external thermal insulation composite systems
UNI EN 13523-10Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water condensation
UNI EN 13523-2Coil coated metals - Test methods - Part 2: Specular gloss
UNI EN 13523-3Coil coated metals - Test methods - Part 3: Colour difference - Instrumental comparison
UNI EN 13657 + EPA 6010CCharacterization of waste - Digestion for subsequent determination of aqua regia soluble portion of elements
UNI EN 14074 par. 6.2.2.Office furniture - Tables and desks and storage furniture - Durability test of extension elements
UNI EN 14074 par. 6.2.3.Office furniture - Tables and desks and storage furniture - Slam open of extension elements
UNI EN 14074 par. 6.3.3.Office furniture - Tables and desks and storage furniture - Durability test on hinged or pivoted doors
UNI EN 14147Natural stones - Determination of resistance to ageing by salt mist
UNI EN 14303 par. 4.3.2Thermal insulation products for building - Maximum service temperature
UNI EN 14303 par. 4.3.3Thermal insulation products for building - Minimum service temperature
UNI EN 14303 par.4.2.2.1Thermal insulation products for building - Linear dimensions
UNI EN 1465Adhesives - Tensile lap-shear strength bonded assemblies
UNI EN 14901-1Ductile iron pipes, fittings and accessories - Requirements and test methods for organic coatings of ductile iron fittings and accessories - Part 1: Epoxy coating (heavy duty)
UNI EN 14901-2Ductile iron pipes, fittings and accessories - Requirements and test methods for organic coatings of ductile iron fittings and accessories - Part 2: Thermoplastic acid modified polyolefin coating (TMPO)
UNI EN 15136Restrizioni su materiali ed oggetti definiti nell Allegato II del Reg.10-2011-UE e smi - BADGE(cas1675-54-3)+derivati, BFDGE(cas 39817-09-9)e NOGE(altri glicidil-eteri novolac) -Migrazione Specifica (mg-kg) BADGE.H2O(cas76002-91-0) BADGE.2H2O(cas76002-91-0) BADGE.HCl(cas13836-48-1) BADGE.2HCl(cas4809-35-2) BADGE.H2O.HCl(cas227947-06-0)
UNI EN 15189Ductile iron pipes, fittings and accessories - External polyurethane coating for pipes - Requirements and test methods
UNI EN 15309Determination of elemental composition by X-ray fluorescence
UNI EN 15340Thermal spraying - Determination of shear load resistance of thermally sprayed coatings
UNI EN 1542Products and systems for the protection and repair of concrete structures - Measurement of bond strength by pull-off
UNI EN 1606Thermal insulating products for building applications - Determination of compressive creep
UNI EN 1607Thermal insulating products for building applications - Determination of tensile strength
UNI EN 17036Conservation of Cultural Heritage - Artificial ageing by simulated solar radiation of the surface of untreated or treated porous inorganic materials
UNI EN 1928Flexible sheets for waterproofing - Bitumen, plastic and rubber sheets - Determination of watertightness
UNI EN 2155-5Aerospace series - Test methods for transparent materials for aircraft glazing - Part 5: Determination of visible light transmission
UNI EN 23270Paints and varnishes and their raw materials - Temperatures and humidities for conditioning and testing
UNI EN 253 par. 4.3.1.1Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Carbon black content and distribution
UNI EN 253 par. 4.3.1.2Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Melt mass flow rate
UNI EN 253 par. 4.3.1.3Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Thermal stability
UNI EN 253 par. 4.3.2.2Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Wall thickness
UNI EN 253 par. 4.3.2.4Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Elongation at break
UNI EN 253 par. 4.3.2.6Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Stress Crack Resistance
UNI EN 253 par. 4.4.2.2Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Cell size
UNI EN 253 par. 4.4.2.3Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Closed cell content
UNI EN 253 par. 4.4.3Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Compressive Strenght
UNI EN 253 par. 4.4.4Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Foam Density
UNI EN 253 par. 4.4.5Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Water Absorption at elevated temperature
UNI EN 253 par. 4.5.7Pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Thermal conductivity in unaged condition
UNI EN 253 par. 5.4.1District heating pipes - Bonded single pipe systems for directly buried hot water networks - Factory made pipe assembly of steel service pipe, polyurethane thermal insulation and a casing of polyethylene - Axial shear strength
UNI EN 3665Aerospace series - Test methods for paints and varnishes - Filiform corrosion resistance test on aluminium alloys
UNI EN 489 par.5.2Water impermeability test
UNI EN 681-1Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber
UNI EN 728Plastics piping and ducting systems - Polyolefin Pipes And Fittings
UNI EN ISO 10456Building materials and products - Hygrothermal properties -- Tabulated design values and procedures for determining declared and design thermal values
UNI EN ISO 105-B02Textiles - Colour fastness to artificial light: Xenon arc fading lamp test
UNI EN ISO 105-E01Textiles - Colour fastness to water
UNI EN ISO 105-X12Textiles - Colour fastness to rubbing
UNI EN ISO 10619-1Rubber and plastics hoses and tubing - Bending test at ambient temperature
UNI EN ISO 1133-1Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics
UNI EN ISO 11357-1Plastics - Differential scanning calorimetry (DSC)
UNI EN ISO 11357-2Plastics - Differential scanning calorimetry (DSC) - Part 2: Determination of glass transition temperature and step height
UNI EN ISO 11357-3Plastics - Differential scanning calorimetry (DSC) - Part 3: Determination of temperature and enthalpy of melting and crystallization
UNI EN ISO 11357-4Plastics - Determination of specific heat capacity
UNI EN ISO 11357-6Plastics - Differential scanning calorimetry (DSC)
UNI EN ISO 11358-1Plastics - Thermogravimetry (TG) of polymers
UNI EN ISO 1158Plastics - Determination of chlorine content
UNI EN ISO 11664-4Colorimetry - CIE 1976 colour space
UNI EN ISO 1172Textile-glass and mineral-filler content
UNI EN ISO 1183-1 - Met.APlastics - Methods for determining the density of non-cellular plastics
UNI EN ISO 1183-3Plastics - Gas pyknometer method
UNI EN ISO 11997-1Paint and varnish - Resistance to cyclic corrosion conditions - Wet (salt fog)-Dry-Humidity
UNI EN ISO 11998Paints and varnishes - Determination of wet-scrub resistance and cleanability of coatings
UNI EN ISO 13468-1Plastics - Determination of the total luminous transmittance of transparent materials
UNI EN ISO 13468-2Plastics - Determination of the total luminous transmittance of transparent materials
UNI EN ISO 13803Paints and varnishes - Determination of haze on paint films at 20 degrees
UNI EN ISO 1463Measurement of coating thickness - Microscopical method
UNI EN ISO 14680-2Paints and varnishes - Determination of pigment content
UNI EN ISO 14713-1Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 1: General principles of design and corrosion resistance
UNI EN ISO 14713-2Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 2: Hot dip galvanizing
UNI EN ISO 148-1Metallic materials - Charpy pendulum impact test
UNI EN ISO 14916Thermal spraying - Determination of tensile adhesive strength
UNI EN ISO 14918Thermal spraying - Qualification testing of thermal sprayers
UNI EN ISO 14919Thermal spraying -- Wires, rods and cords for flame and arc spraying - Classification -- Technical supply conditions
UNI EN ISO 15091Paints and varnishes - Determination of electrical conductivity and resistance (ISO 15091:2020)
UNI EN ISO 15110Paints and varnishes - Artificial weathering including acidic deposition
UNI EN ISO 1513Paints and varnishes - Examination and preparation of test samples
UNI EN ISO 15184Paints and varnishes - Film hardness by pencil test
UNI EN ISO 1519Paints and varnishes - Bend test (cylindrical mandrel) (ISO 1519:2011)
UNI EN ISO 1520Paints and varnishes - Cupping test
UNI EN ISO 15512Plastics - Determination of water content
UNI EN ISO 16276-2Paint systems - Cross-cut testing and X-cut testing
UNI EN ISO 16474-1Paints and varnishes - Methods of exposure to laboratory light sources
UNI EN ISO 16474-2Paints and varnishes - Methods of exposure to laboratory light sources
UNI EN ISO 16474-3Paints and varnishes - Methods of exposure to laboratory light sources
UNI EN ISO 16773-1Electrochemical impedance spectroscopy (EIS) on coated and uncoated metallic specimens - Part 1: Terms and definitions (ISO 16773-1:2016)
UNI EN ISO 16773-2Electrochemical impedance spectroscopy (EIS) on coated and uncoated metallic specimens - Part 2: Collection of data (ISO 16773-2:2016)
UNI EN ISO 16773-3Electrochemical impedance spectroscopy (EIS) on coated and uncoated metallic specimens - Part 3: Processing and analysis of data from dummy cells (ISO 16773-3:2016)
UNI EN ISO 16773-4Electrochemical impedance spectroscopy (EIS) on coated and uncoated metallic specimens - Part 4: Examples of spectra of polymer-coated and uncoated specimens (ISO 16773-4:2017)
UNI EN ISO 16925Paints and varnishes - Determination of the resistance of coatings to pressure water-jetting (ISO 16925:2014)
UNI EN ISO 17463Paints and varnishes - Guidelines for the determination of anticorrosive properties of organic coatings by accelerated cyclic electrochemical technique (ISO 17463:2014)
UNI EN ISO 175Plastics - Determination of the effects of immersion in liquid chemicals
UNI EN ISO 178Plastics - Determination of flexural properties
UNI EN ISO 17872Paints and varnishes - Guidelines for the introduction of scribe marks through coatings on metallic panels for corrosion testing
UNI EN ISO 179-1Plastics - Determination of Charpy impact properties - Part 1
UNI EN ISO 179-2Plastics - Determination of Charpy impact properties Instrumented impact test
UNI EN ISO 180Plastics - Determination of Izod impact strength
UNI EN ISO 1923Cellular plastics and rubbers - Determination of linear dimensions
UNI EN ISO 19403-1Paints and varnishes - Wettability - Part 1: Terminology and general principles (ISO 19403-1:2017)
UNI EN ISO 19403-2Paints and varnishes - Wettability - Part 2: Determination of the surface free energy of solid surfaces by measuring the contact angle (ISO 19403-2:2017)
UNI EN ISO 19403-3Paints and varnishes - Wettability - Part 3: Determination of the surface tension of liquids using the pendant drop method (ISO 19403-3:2017)
UNI EN ISO 19403-4Paints and varnishes - Wettability - Part 4: Determination of the polar and dispersive fractions of the surface tension of liquids from an interfacial tension (ISO 19403-4:2017)
UNI EN ISO 19403-5Paints and varnishes - Wettability - Part 5: Determination of the polar and dispersive fractions of the surface tension of liquids from contact angles measurements on a solid with only a disperse contribution to its surface energy (ISO 19403-5:2017)
UNI EN ISO 19403-6Paints and varnishes - Wettability - Part 6: Measurement of dynamic contact angle (ISO 19403-6:2017)
UNI EN ISO 2039-1Plastics - Determination of hardness
UNI EN ISO 20567-1Paints and varnishes - Determination of stone-chip resistance of coatings
UNI EN ISO 20567-2Paints and varnishes - Determination of stone-chip resistance of coatings Single-impact test with a guided impact body
UNI EN ISO 2063-2Thermal spraying — Zinc, aluminium and their alloys - Part 2: Execution of corrosion protection systems
UNI EN ISO 2160Petroleum products - Corrosiveness to copper - Copper strip test
UNI EN ISO 2178Non-magnetic coatings on magnetic substrates - Measurement of coating thickness
UNI EN ISO 21809-1 Annex AExternal coatings for buried or submerged pipelines used in pipeline transportation systems - Thicknesses of the coating
UNI EN ISO 21809-1 Annex BPetroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems Polyolefin coatings (3-layer PE and 3-layer PP) - Holiday detection test
UNI EN ISO 21809-1 Annex CExternal coatings for buried or submerged pipelines used in pipeline transportation systems - Peel strenght test
UNI EN ISO 21809-1 Annex DExternal coatings for buried or submerged pipelines used in pipeline transportation systems - Thermal analysis of epoxy and cured epoxy coating film with Tg<115.C
UNI EN ISO 21809-1 Annex EExternal coatings for buried or submerged pipelines used in pipeline transportation systems - Impact strenght
UNI EN ISO 21809-1 Annex FExternal coatings for buried or submerged pipelines used in pipeline transportation systems - Indentation test
UNI EN ISO 21809-1 Annex G.1Polyolefin coatings (3-layer PE and 3-layer PP) - UV ageing
UNI EN ISO 21809-1 Annex G.2Polyolefin coatings (3-layer PE and 3-layer PP) - Thermal ageing
UNI EN ISO 21809-1 Annex HExternal coatings for buried or submerged pipelines used in pipeline transportation systems - Cathodic disbondment test
UNI EN ISO 21809-1 Annex IExternal coatings for buried or submerged pipelines used in pipeline transportation systems - Flexibility test
UNI EN ISO 21809-1 Annex JExternal coatings for buried or submerged pipelines used in pipeline transportation systems - Gel time of epoxy powder
UNI EN ISO 21809-1 Annex KExternal coatings for buried or submerged pipelines used in pipeline transportation systems - Moisture content
UNI EN ISO 21809-1 Annex LHot water immersion test
UNI EN ISO 21809-1 Annex MExternal coatings for buried or submerged pipelines used in pipeline transportation systems - Density of epoxy powder
UNI EN ISO 21809-2 par. A.10Single layer fusion-bonded epoxy coatings - Cathodic disbondment of high temperature coatings ( >95°C)
UNI EN ISO 21809-2 par. A.11Single layer fusion-bonded epoxy coatings - Interface contamination
UNI EN ISO 21809-2 par. A.12Single layer fusion-bonded epoxy coatings - Cross section and Interface porosity
UNI EN ISO 21809-2 par. A.13Single layer fusion-bonded epoxy coatings - Flexibility of the coating
UNI EN ISO 21809-2 par. A.14Single layer fusion-bonded epoxy coatings - Resistance to impact of the coating
UNI EN ISO 21809-2 par. A.15Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems Single layer fusion-bonded epoxy coatings - Cathodic disbondment of strained coating
UNI EN ISO 21809-2 par. A.16Single layer fusion-bonded epoxy coatings - Hot-water adhesion of the coating
UNI EN ISO 21809-2 par. A.2Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems - Single layer fusion-bonded epoxy coatings - Cure time of the epoxy powder
UNI EN ISO 21809-2 par. A.3Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems - Single layer fusion-bonded epoxy coatings - Gel time of the epoxy powder
UNI EN ISO 21809-2 par. A.4Single layer fusion-bonded epoxy coatings - Dry adhesion test
UNI EN ISO 21809-2 par. A.5Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems - Single layer fusion-bonded epoxy coatings - Total volatile-moisture content of the epoxy powder — Mass loss - Procedure A
UNI EN ISO 21809-2 par. A.6Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems Single layer fusion-bonded epoxy coatings - Particle size of the epoxy powder
UNI EN ISO 21809-2 par. A.7Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems - Single layer fusion-bonded epoxy coatings - Density of the epoxy powder
UNI EN ISO 21809-2 par. A.8Single layer fusion-bonded epoxy coatings - Thermal analysis of epoxy powder and cured coating film
UNI EN ISO 21809-2 par. A.9Single layer fusion-bonded epoxy coatings - Cathodic disbondment of coatings for standard temperatures up to 95°C
UNI EN ISO 21809-3 Annex BField joint coatings - Inspection of thickness
UNI EN ISO 21809-3 Annex CField joint coatings - Holiday detection test
UNI EN ISO 21809-3 Annex DField joint coatings - Impact test
UNI EN ISO 21809-3 Annex EField joint coatings - Indentation test
UNI EN ISO 21809-3 Annex GField joint coatings - Cathodic disbondment test
UNI EN ISO 21809-3 Annex HField Joint coatings - Peel strenght
UNI EN ISO 21809-3 Annex IField joint coatings - Hot water immersion test
UNI EN ISO 21809-3 Annex JField joint coatings - Lap shear strenght
UNI EN ISO 21809-3 Annex QField Joint Coatings - Resistance to removal
UNI EN ISO 22088-2Plastics - Determination of resistance to environmental stress cracking (ESC) Constant tensile load method
UNI EN ISO 22631Adhesives - Peel test
UNI EN ISO 2360Non-conductive coatings on non-magnetic electrically conductive basis materials - Measurement of coating thickness
UNI EN ISO 2409Paints and varnishes on metallic substrate - Cross-cut test
UNI EN ISO 2555Plastics -- Resins in the liquid state or as emulsions or dispersions - Determination of apparent viscosity using a single cylinder type rotational viscometer method
UNI EN ISO 2808Paints and varnishes on metallic substrate - Determination of film thickness
UNI EN ISO 2811-1Paints and varnishes - Determination of density
UNI EN ISO 2812-1Paints and varnishes on metallic substrate - Determination of resistance to liquids
UNI EN ISO 2812-2Paints and varnishes on metallic substrate - Determination of resistance to liquids
UNI EN ISO 2812-3Paints and varnishes - Determination of resistance to liquids - Part 3 Method using an absorbent medium
UNI EN ISO 2812-4Paints and varnishes - Determination of resistance to liquids
UNI EN ISO 2812-5Paints and varnishes - Determination of resistance to liquids Temperature-gradient oven method
UNI EN ISO 2813Paints and varnishes - Determination of gloss value at 20 degrees, 60 degrees and 85 degrees
UNI EN ISO 2819Metallic coatings on metallic substrates - Electrodeposited and chemically deposited coatings
UNI EN ISO 2884-2Paints and varnishes - Disc or ball viscometer operated at a specified speed
UNI EN ISO 306Plastics - Determination of Vicat softening temperature
UNI EN ISO 307Plastics - Polyamides - Determination of viscosity number
UNI EN ISO 3231Paints and varnishes - Determination of resistance to humid atmospheres containing sulfur dioxide
UNI EN ISO 3233-2Paints and varnishes - Method using the determination of non-volatile-matter content and determination of dry film density
UNI EN ISO 3248Paints and varnishes -- - Determination of the effect of heat
UNI EN ISO 3251Paints, varnishes e plastics - Determination of non-volatile-matter content
UNI EN ISO 3451-1Plastics - Determination of ash General methods
UNI EN ISO 3611Geometrical product specifications (GPS) - Dimensional measuring equipment: Micrometers for external measurements - Design and metrological characteristics (ISO 3611:2010)
UNI EN ISO 3696Water for analytical laboratory use
UNI EN ISO 4288Surface condition Profile method - Rules and procedures for determining the surface condition.
UNI EN ISO 4623-1Paints and varnishes - Determination of resistance to filiform corrosion Steel substrates
UNI EN ISO 4624Paints and varnishes on metallic substrate - Pull-off test for adhesion
UNI EN ISO 4628-1Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance
UNI EN ISO 4628-10Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance
UNI EN ISO 4628-2Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance
UNI EN ISO 4628-3Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects and of intensity of uniform changes in appearance
UNI EN ISO 4628-4Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance
UNI EN ISO 4628-5Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance
UNI EN ISO 4628-6Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance
UNI EN ISO 4628-7Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance
UNI EN ISO 4628-8Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance
UNI EN ISO 489Plastics - Determination of refractive index
UNI EN ISO 4892-1Plastics - Methods of exposure to laboratory light sources
UNI EN ISO 4892-2Plastics - Methods of exposure to laboratory light sources
UNI EN ISO 4892-3Plastics - Methods of exposure to laboratory light sources
UNI EN ISO 527-1Plastics - Determination of tensile properties
UNI EN ISO 527-2Plastics - Determination of tensile properties
UNI EN ISO 527-3Plastics - Tensile properties - test conditions for films and sheets
UNI EN ISO 527-4 TRAZIONI su COMPOSITIPlastics - Determination of tensile properties Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
UNI EN ISO 60Apparent density of material
UNI EN ISO 62Plastics - Determination of water absorption
UNI EN ISO 6259-1Thermoplastics pipes - Determination of tensile properties
UNI EN ISO 6270-1Paints and varnishes - Determination of resistance to humidity
UNI EN ISO 6270-2Paints and varnishes on metallic substrate - Determination of resistance to humidity
UNI EN ISO 6272-1Paints and varnishes - Rapid-deformation (impact resistance) tests
UNI EN ISO 6272-2Paints and varnishes - Rapid-deformation (impact resistance) tests
UNI EN ISO 6504-1Paints and varnishes - Determination of hiding power — Part 1: Kubelka-Munk method
UNI EN ISO 6506-1Metallic materials - Brinell hardness
UNI EN ISO 6507-1Metallic materials - Vickers hardness test
UNI EN ISO 6508-1Metallic materials - Rockwell hardness test
UNI EN ISO 6892-1Metallic materials - Tensile testing - Method of test at room temperature
UNI EN ISO 7599 par.6.3Anodizing of aluminium and its alloys - General specifications for anodic oxidation coatings on aluminium
UNI EN ISO 7783Paints and varnishes - Determination of water-vapour transmission properties — Cup method
UNI EN ISO 7784-2Paints and varnishes - Determination of resistance to abrasion
UNI EN ISO 8407Corrosion of metals and alloys - Removal of corrosion products from corrosion test specimens
UNI EN ISO 844Rigid cellular plastics - Determination of compression properties
UNI EN ISO 845Cellular plastics and rubbers - Determination of apparent density
UNI EN ISO 8502-4Preparation of steel substrates before application of paint and related products - Tests for the assessment of surface cleanliness
UNI EN ISO 868Plastics and ebonite - Determination of indentation hardness by means of a durometer
UNI EN ISO 9227Organic and inorganic coatings on metallic substrate - Corrosion tests in artificial atmospheres
UNI EN ISO 9227 - AceticaAnodic and organic coatings on aluminium - Corrosion in acetic acid salt spray (AASS)
UNI ISO 1817Rubber vulcanized or thermoplastic - Determination of the effect of liquids
UNI ISO 188Rubber, vulcanized or thermoplastic - Accelerated ageing and heat resistance tests
UNI ISO 3795Road vehicles and tractors and machinery for agriculture and forestry. - Determination of burning behaviour of interior materials.
UNI ISO 4650Identification - Infrared spectrometric methods
UNI ISO 815-1Rubber, vulcanized or thermoplastic - Determination of compression set At ambient or elevated temperatures
VCS 1027, 1449Accelerated corrosion test, version II – ACT II
VDA 237-300Surface protection brake calipers - Thermal shock
VDA 238-100Metallic materials - Plate bending test for metallic materials
VW 50180Components, Semi-Finished Products and Materials in the Vehicle Interior - Emission Behavior
VW 50181Lights with transparent covering pane - Fogging characteristics
VW 50195Automobile Paint Coatings - Colorimetric Evaluation
VW 80000 K-06Electric and Electronic Components in Motor Vehicles up to 3.5 t - K-06 Salt spray test with operation, exterior
VW PV 1200Paints and varnishes - Testing of Resistance to Environmental Cycle Test (+80--40)°C
VW PV 1210Body and Add-On Parts/Hang-On Parts - Cyclic corrosion Test
VW PV 1303Xenon Arc Light Aging of Vehicle Interior Components
VW PV 1306Determining the Tackiness of Polypropylene Parts
VW PV 1503Paint and coatings - Pressure washer test
VW PV 2005Paints and varnishes - Testing of resistance to enviromental cycle test
VW PV 2044 KL3KL3 - Heat and humidity aging
VW PV 2044 KL4KL4 - Low-temperature aging
VW PV 2044 KWL1KWL1 – Hot, dry climate with cold exposure
VW PV 2044 KWL2KWL2 – Humid, warm climate
VW PV 2044 KWL3KWL3 – Environmental simulation without radiation influence
VW PV 3.3.3Paints and Varnishes - Scratch Resistance Testing of Clear Coats
VW PV 3015Fogging behaviour of materials used in the vehicle interior
VW PV 3357Behavior on Flame Exposure with a Burner
VW PV 3905Organic materials - Ball drop test
VW PV 3929Non-Metallic Materials - Weathering in Dry, Hot Climate
VW PV 3930Non-Metallic Materials - Weathering in Humid, Hot Climate
VW PV 3966Stress Whitening Properties (Ball Drop Test)
VW TL 1010Materials for Vehicle Interiors - Burning Behavior
VW TL 207 Tab.2 No.1Reflective Coatings on Enclosed Plastic Reflectors - PV 1200 - 8 cycles
VW TL 207 Tab.2 No.2Reflective Coatings on Enclosed Plastic Reflectors - Heat aging
VW TL 207 Tab.2 No.3Reflective Coatings on Enclosed Plastic Reflectors - ISO 6270-2 - 48h
VW TL 211 No. 1.1Gloss value
VW TL 211 No. 1.2.1Visual matching
VW TL 211 No. 1.2.2Colorimetric evaluation
VW TL 211 No. 1.3Wave-scan
VW TL 211 No. 2Coating thickness
VW TL 211 No. 3.1Stone impact test
VW TL 211 No. 3.2Steam-jet test
VW TL 211 No. 3.3Cross-cut test
VW TL 211 No. 3.4Resistance to humidity: degree of blistering and adhesion by steam-jet test and cross-cut test.
VW TL 211 No. 4.1Environmental cycle test
VW TL 211 No. 4.2Coating of Plastic Exterior Parts - Heat aging in a forced-air oven
VW TL 211 No. 5Corrosion resistance: 20 cycles as per PV1200, then 240h pf CASS - ISO 9227.
VW TL 211 No. 7.1Resistance to chemicals: FAM test fuel
VW TL 211 No. 7.10Resistance to chemicals: artificial bird droppings
VW TL 211 No. 7.11Resistance to chemicals: Tree resine (ISO 2812-4 A.4.1)
VW TL 211 No. 7.2Resistance to chemicals: E10 gasoline
VW TL 211 No. 7.3Resistance to chemicals: B7 diesel fuel
VW TL 211 No. 7.4Resistance to chemicals: Isopropanol
VW TL 211 No. 7.5Resistance to chemicals: sodium hydroxide solution
VW TL 211 No. 7.6Resistance to chemicals: sulfuric acid
VW TL 211 No. 7.7Resistance to chemicals: 10 hydrochloric acid
VW TL 211 No. 7.8Resistance to chemicals: water (grade 3)
VW TL 211 No. 7.9Resistance to chemicals: nitrocellulose thinner
VW TL 211 No. 8.1.1Weathering in humid, hot climate as per PV 3930 - 1 year
VW TL 211 No. 8.1.2Weathering in dry, hot climate as per PV 3929 - 1 year
VW TL 211 No. 8.2.1Weathering in humid, hot climate as per PV 3930 - 2 years
VW TL 211 No. 8.2.2Weathering in dry, hot climate as per PV 3929 - 2 yeas
VW TL 227 par.3.10.1Corrosion cycle test
VW TL 227 par.3.10.2Condensation atmosphere with constant humidity
VW TL 227 par.3.11Resistance to chemicals
VW TL 227 par.3.8Adhesion and brittleness
VW TL 227 par.3.9Stone-chip resistance
VW TL 256 No.10Impact test at low temperature
VW TL 256 No.11Resistance to chemicals
VW TL 256 No.6Coating adhesion (cross-cut test)
VW TL 256 No.7Stone-chip resistance
VW TL 256 No.8.1Corrosion cycle test (PV1210)
VW TL 256 No.8.2Condensation atmosphere with constant humidity
VW TL 256 No.9.1Heat aging
VW TL 256 No.9.2Low-temperature aging
XP A 35-037-1 par.7.1Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Overall diameter
XP A 35-037-1 par.7.2Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Straightness
XP A 35-037-1 par.7.4.1Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Weight of protection product per unit length
XP A 35-037-1 par.7.5.1Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Sheath thickness (one cross section)
XP A 35-037-1 par.7.5.10Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Resistance to ionizing radiation
XP A 35-037-1 par.7.5.11Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Resistance after exposure at temperature
XP A 35-037-1 par.7.5.13Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Resistance to shocks
XP A 35-037-1 par.7.5.2Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Sheath weight per unit length
XP A 35-037-1 par.7.5.5 +D6.1Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Leaktightness static test
XP A 35-037-1 par.7.5.6Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Initial resistance to friction
XP A 35-037-1 par.7.5.8Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Stress cracking strength
XP A 35-037-1 par.7.5.9Steel products - Protected and sheathed high strength steel strands - Part 1 : general requirements - Resistance to etching agents: N°1 acid n°1 base n°1 solvent and mineral oil from sheath (to be supplied by the client) Immersion temperature and duration:+23°C-168hours